CB installed [Archive] - Hummer Forums by Elcova

Sewie

10-24-2005, 03:20 AM

The kit included an 18' fireflex cable. I ran the cable down the A-pillar and behind the quarter panel. I had to clip the A-pillar trim a little so it would sit flat with the cable running through.

Sewie

10-24-2005, 03:20 AM

I ran the coax under the drivers side and up into the door sill. There are some existing grommets underneath.

Sewie

10-24-2005, 03:21 AM

I tapped into an existing aux. line (Aux. B+) and ground under the dash. It is not switched so the CB can work without the key in the ignition.

Sewie

10-24-2005, 03:21 AM

I mounted the remote unit inside the center console and tucked the excess cables underneath the center trim. The pigtail for the mic fits through a gap in the console and hangs out the passenger side.

Sewie

10-24-2005, 03:22 AM

A pic of everything put back together.

Sewie

10-24-2005, 03:23 AM

I added a fold-over mount so I can drop the antenna when I go through a low-hanging area. The reason I mounted the antenna where I did is so I can reach it out the drivers window. Thanks to the H2 guys for that idea.

Sewie

10-24-2005, 03:23 AM

The antenna. I need to bend the mount a little. It is flush-mounted to the roof trim so the antenna leans out a little.

The Green Lantern

10-24-2005, 04:29 AM

looks great, I will do the same where you put the unit inside the center console, but how did you remove the face cover of the center console? and if you could give us more detail on how did you tap the power?...thanks.

Sewie

10-24-2005, 03:10 PM

<BLOCKQUOTE class="ip-ubbcode-quote"><div class="ip-ubbcode-quote-title">quote:</div><div class="ip-ubbcode-quote-content">Originally posted by The Green Lantern:
looks great, I will do the same where you put the unit inside the center console, but how did you remove the face cover of the center console? and if you could give us more detail on how did you tap the power?...thanks. </div></BLOCKQUOTE>

The face plate is held in with clips. Move the shifter all the way back, stick your fingers in the aux outlets and pull up/out. There are about 4-5 plugs you have to remove to get it all the way out.

For the power, the wires should all be labeled. They were bundled just above the light you see in the picture.

One note about that mounting location. Make sure you tune your antenna before you mount the box since it is pretty hard to get to afterwards.

Klint

10-24-2005, 03:56 PM

Hey bud, how did you get your a pillers off? Thanks for the pictures looks great man!

Sewie

10-24-2005, 08:33 PM

<BLOCKQUOTE class="ip-ubbcode-quote"><div class="ip-ubbcode-quote-title">quote:</div><div class="ip-ubbcode-quote-content">Originally posted by Klint:
Hey bud, how did you get your a pillers off? Thanks for the pictures looks great man! </div></BLOCKQUOTE>

Pull the rubber door seal back and there are two screws on the side.

DDWH

10-24-2005, 09:11 PM

Sweet looking install Sewie!

FormerJeeper

10-27-2005, 01:26 PM

Great job!

I have the same CB left over from my Jeepin days.
I was wondering (read procastrinating http://www.elcova.com/infopop/emoticons/icon_wink.gif ) about how to do it http://www.elcova.com/infopop/emoticons/icon_smile.gif

Thanks for a gr8 idea!

-C

HummBebe

10-27-2005, 11:35 PM

I am muy impressed with your expertise! Excellent install http://www.elcova.com/infopop/emoticons/icon_smile.gif

x-humm

11-11-2005, 02:14 AM

Hey Sewie,

Where did you get your cobra cb radio and antenna. I've been looking around and nobody have them in stock. ALl the places I found are mail orders.

Thanks

MyxH3

11-11-2005, 02:25 AM

I like the Radio/antenna set up I had the same one in my Xterra. Saved the radio but the antenna went.

Sewie

11-11-2005, 02:50 AM

I ordered everything online. I got the CB from Beach Audio (http://www.beachaudio.com) and the antenna and other stuff from Walcott CB (http://www.walcottcb.com).

2xtreme

12-15-2005, 07:09 PM

Sewie how do you like the CB radio you installed back in Oct. Is everything working good, and or have you changed anything from your origional install? Wondering because I am thinking about installing one in my H3.

H3HUMVEE

12-15-2005, 08:10 PM

thanks for the pictures and info .. I'm getting ready to install a yaesu 897 in my H3

Sewie

12-15-2005, 08:12 PM

<BLOCKQUOTE class="ip-ubbcode-quote"><div class="ip-ubbcode-quote-title">quote:</div><div class="ip-ubbcode-quote-content">Originally posted by 2xtreme:
Sewie how do you like the CB radio you installed back in Oct. Is everything working good, and or have you changed anything from your origional install? Wondering because I am thinking about installing one in my H3. </div></BLOCKQUOTE>

Everything's working ok but I am thinking about moving the antenna to the rear bumper and adding a spring mount. Most of the areas I've been I can't leave the antenna up so transmitting sucks.

2xtreme

12-16-2005, 11:37 AM

keep us posted on the changes, and you did so well at posting pics of the install the 1st time it would be a shame if you didn't this time. http://www.elcova.com/infopop/emoticons/icon_biggrin.gif thanks for the reply.

BABHUMV

12-16-2005, 01:27 PM

I just installed the same CB. I just tapped into the power for the right CIg lighter socket. It is power on all the time and the wires are right there.
I have ordered a new antenna mount so I can mount the antenna on the left front fender in the same (but opposite) position as the radio antenna on the right.
I ordered a 4 foot Firestik so I can flag it when necessary, but I think I will order a 2 footer for around town.

Thanks for the great shots and info.

fourfourto

12-16-2005, 01:35 PM

Just to let you know the cig/accy lighter/ socket shuts off after 20 min(of shutting off truck) if accy is left on.

MarK M

12-29-2005, 06:04 AM

CB install looks nice!

question... with the motorola talkabouts whats the need for CB's?

regards,

f5fstop

12-29-2005, 01:15 PM

<BLOCKQUOTE class="ip-ubbcode-quote"><div class="ip-ubbcode-quote-title">quote:</div><div class="ip-ubbcode-quote-content">Originally posted by fourfourto:
Just to let you know the cig/accy lighter/ socket shuts off after 20 min(of shutting off truck) if accy is left on. </div></BLOCKQUOTE>

It should never shut off, until the battery goes dead. Per the wiring diagrams, the accessory power outlets are powered directly from the B+ terminal of the battery, through one of two fuses. One 20A fuse (#51) protects one of the front accessory plugs, and a 30A fuse (45) protects the other front power outlet, as well as the rear power outlet.
The diagrams show no BCM control over these circuits.
The BCM will power down the interior lights if they are left on, and there is no switch movement for 20 minutes. This prevents the battery from going dead due to interior lights being left on.

BABHUMV

12-29-2005, 04:22 PM

<BLOCKQUOTE class="ip-ubbcode-quote"><div class="ip-ubbcode-quote-title">quote:</div><div class="ip-ubbcode-quote-content">Originally posted by fourfourto:
Just to let you know the cig/accy lighter/ socket shuts off after 20 min(of shutting off truck) if accy is left on. </div></BLOCKQUOTE>

A dead battery in the morning contradicts this statement. The Power Supply plugs in the dash are hot all the time and do not turn off in 20 minutes. Found out the hard way.

Got the antenna mounted. It now offsets the factory radio antenna by being mounted on the opposite side in the same location on the fender. Ran the antenna wire from behind glove box, out a grommet hole in the frame above the front door hinge (silicon sealed the grommet when done) up and over the top behind the cowling trim and into the other side fender. This way it was invisible and does not interfere with anything.

The Green Lantern

12-29-2005, 07:15 PM

<BLOCKQUOTE class="ip-ubbcode-quote"><div class="ip-ubbcode-quote-title">quote:</div><div class="ip-ubbcode-quote-content">Originally posted by BABHUMV:
Got the antenna mounted. It now offsets the factory radio antenna by being mounted on the opposite side in the same location on the fender. Ran the antenna wire from behind glove box, out a grommet hole in the frame above the front door hinge (silicon sealed the grommet when done) up and over the top behind the cowling trim and into the other side fender. This way it was invisible and does not interfere with anything. </div></BLOCKQUOTE>

- do you have a pic from the side?

thanks

BABHUMV

12-29-2005, 11:06 PM

<BLOCKQUOTE class="ip-ubbcode-quote"><div class="ip-ubbcode-quote-title">quote:</div><div class="ip-ubbcode-quote-content">Originally posted by The Green Lantern:
- do you have a pic from the side?

thanks </div></BLOCKQUOTE>

Hope these shots help, couldn't get a good angle.
one cool thing, is that you do not see it when driving, the A pillar hides it very nicely.