Need water pump install instructions

[Pirana]

If anyone has any info on water pump install...never done a GM one before. Any tips, pics, instructions, CDs would be greatly appreciated. :grouphug:

[HUMTECH]

Important: All gaskets surfaces are to be free of oil or other foreign material during assembly.

Notice: Refer to Fastener Notice (http://service.gm.com/servlets/CellHandler?CellId=10105&RefDoc=861554&evc=sm) in Cautions and Notices.


http://service.gm.com/tif.gif (http://service.gm.com/servlets/RetrieveTif?pic=260121)
<LI type=1>Install the water pump and NEW gaskets. <LI type=1>Install the water pump bolts.
Tighten
<LI type=1>Tighten the water pump bolts a first pass to 15 N?m (11 lb ft).
Tighten the water pump bolts a final pass to 30 N?m (22 lb ft).
http://service.gm.com/tif.gif (http://service.gm.com/servlets/RetrieveTif?pic=660665)
<LI type=1>Install the heater inlet hose to the water pump. <LI type=1>Position the heater inlet hose clamp at the water pump.

http://service.gm.com/tif.gif (http://service.gm.com/servlets/RetrieveTif?pic=659180)
<LI type=1>Install the surge tank outlet hose to the water pump. <LI type=1>Position the surge tank outlet hose clamp at the water pump.

http://service.gm.com/tif.gif (http://service.gm.com/servlets/RetrieveTif?pic=659509)
<LI type=1>Install the outlet hose to the water pump. <LI type=1>Position the outlet hose clamp at the water pump. <LI type=1>Install the accessory drive belt. Refer to Drive Belt Replacement - Accessory (http://service.gm.com/servlets/CellHandler?CellId=44132&RefDoc=861554&evc=sm) . <LI type=1>Install the fan blade. Refer to Fan Replacement (http://service.gm.com/servlets/CellHandler?CellId=37301&RefDoc=861554&evc=sm) .

http://service.gm.com/tif.gif (http://service.gm.com/servlets/RetrieveTif?pic=659418)
<LI type=1>Install the inlet hose to the water pump. <LI type=1>Position the inlet hose clamp at the water pump.

http://service.gm.com/tif.gif (http://service.gm.com/servlets/RetrieveTif?pic=659465)
<LI type=1>Install the engine vent inlet hose to the radiator hose clips.

http://service.gm.com/tif.gif (http://service.gm.com/servlets/RetrieveTif?pic=832908)
Important: Align the arrow at the throttle body end of the duct with the throttle body attaching stud.

<LI type=1>Install the air cleaner outlet duct. <LI type=1>Install the radiator inlet hose clip to the outlet duct. <LI type=1>Tighten the air cleaner outlet duct clamps at the following locations: ? Throttle body

? MAF/IAT sensor
Tighten
Tighten the air cleaner outlet duct clamp screws to 7 N?m (62 lb in).
Fill the cooling system. Refer to Draining and Filling Cooling System (http://service.gm.com/servlets/CellHandler?CellId=37226&RefDoc=861554&evc=sm) .

[Pirana]

thank you very much for your response...

Did everything today, no problems :beerchug: