View Full Version : Need help removing back hatch handle
cybordolphin
04-10-2010, 09:12 AM
Anyone know the proceedure for replacing the back plastic hatch handle on a 2004 H2?
Any help is greatly appreciated!
HUMTECH
04-10-2010, 07:27 PM
Rear License Plate Pocket Replacement (SUV)
<A href="http://gsi.xw.gm.com/si/cellHandler.do?cellId=9635&refDoc=833595&from=sm#ss1-833520">Removal Procedure
Open the liftgate.
Remove the liftgate trim panel. Refer to Liftgate Trim Panel Replacement (http://gsi.xw.gm.com/si/cellHandler.do?cellId=9544&refDoc=833520&from=sm) .
http://gsi.xw.gm.com/si/images/tif.gif (http://gsi.xw.gm.com/si/showTif.do?image=832874)
Remove the latch cable handle connection by releasing the retainer (1) and removing the cable end from the handle arm.
http://gsi.xw.gm.com/si/images/tif.gif (http://gsi.xw.gm.com/si/showTif.do?image=880649)
Disconnect the 2 license plate pocket electrical connectors (3).
http://gsi.xw.gm.com/si/images/tif.gif (http://gsi.xw.gm.com/si/showTif.do?image=1453816)
Remove the 6 nuts (5) retaining the plate pocket to the liftgate.
Release the 4 clips (3) retaining the license plate pocket to the liftgate (2).
http://gsi.xw.gm.com/si/images/tif.gif (http://gsi.xw.gm.com/si/showTif.do?image=1453815)
Remove the license plate pocket (2) from the liftgate (3).<A href="http://gsi.xw.gm.com/si/cellHandler.do?cellId=9635&refDoc=833595&from=sm#ss2-833520">Installation Procedure
http://gsi.xw.gm.com/si/images/tif.gif (http://gsi.xw.gm.com/si/showTif.do?image=1453815)
Place the license plate pocket (2) in position on the liftgate (3), ensuring all of the retaining clips are fully seated.Notice: Refer to Fastener Notice (http://gsi.xw.gm.com/si/cellHandler.do?cellId=10105&refDoc=833520&from=sm) in the Preface section.
http://gsi.xw.gm.com/si/images/tif.gif (http://gsi.xw.gm.com/si/showTif.do?image=1453816)
Install the 6 nuts (5) retaining the license plate pocket to the liftgate.Tighten
Tighten the nuts to 4.5 N?m (40 lb in).
Connect the 2 license plate electrical connectors.
http://gsi.xw.gm.com/si/images/tif.gif (http://gsi.xw.gm.com/si/showTif.do?image=832874)
Attach the latch control cable handle connection by installing the cable end into the handle arm (2) and securing the retainer (1).
Install the liftgate trim panel. Refer to Liftgate Trim Panel Replacement (http://gsi.xw.gm.com/si/cellHandler.do?cellId=9544&refDoc=833520&from=sm) .? 2010 General Motors. All rights reserved.
Hi HUMTECH, i couldn't have said it better myself:perfect10s: to the mechanics in canada
vBulletin v3.0.7, Copyright ©2000-2025, Jelsoft Enterprises Ltd.