PDA

View Full Version : KIMS YELLOW RANCHO LIFT

floridahummer
10-30-2005, 08:56 PM
HERE THEY ARE
timgco
10-30-2005, 09:10 PM
Very nice! How does it handle? at HWY speeds? When going around corners does it lean more than stock or feel tippy? How is the overall ride compared to stock? Any more pics of the susp. components installed?

LOVE IT! more pics, more pics, more pics.
DDWH
10-30-2005, 10:18 PM
LOOKS AWESOME!
floridahummer
10-30-2005, 10:24 PM
Originally posted by timgco:
Very nice! How does it handle? at HWY speeds? When going around corners does it lean more than stock or feel tippy? How is the overall ride compared to stock? Any more pics of the susp. components installed?

LOVE IT! more pics, more pics, more pics.

As to how does it rides. Suprising enough it feels more stable than stock at slow speeds 0-45mph. Corners are great. Does not feel tippy. As far as 55 and above it just changes lanes quicker but still very stable. Here in florida we have speed limits up to 70mph. At
85(wich is what the speedo read still uncalibrated for new tires) that was about as fast as i wanted to go.
hmrlvr
10-30-2005, 10:36 PM
Looks awesome. Thanks for the pix
timgco
10-30-2005, 10:36 PM
Originally posted by floridahummer:
At
85(wich is what the speedo read still uncalibrated for new tires) that was about as fast as i wanted to go.

Because of a ticket? or because of being unstable in some way? 75mph to 80mph is common for me when going to CO Springs from Denver, so this is why I am asking again... just to double check. Sorry for all the Q's.
evomind
10-31-2005, 02:25 PM
looks great.....
urs handles relatively good because u went with 20" rims, and u dont have a whole lot of sidewall...so less sidewall flex.
i have a few pics posted.....
VTSTOMPER
10-31-2005, 02:29 PM
HUGE HUGE HUGE!

Looks nice! Rubbin' racin'
MxHonda
10-31-2005, 11:39 PM
What is the pic of that gave you more bottom end response?
floridahummer
11-01-2005, 11:35 AM
Originally posted by MxHonda:
What is the pic of that gave you more bottom end response?


I installed throttle body spacer. Forgot to show it installed. beware tougher than instructions. This is not a Colorado and instructions do not adress h3 aplication. Remove all 4 inch ducts. Then remove abs plenum ( two bolts on r side ) Make shure to place new gasket on oposite side of factory green gasket so that there is a gasket on both sides of spacer. Finally make shure to reinstall small hose on bottom of abs plenum befor reinstalling the ducts. P.S. This may be a little difficult due to the new throttle bod spacer. I solved this by applying a small dab of vasoline on male end of ducts to allow them to slide in easier. Dont laugh it worked.
evomind
11-01-2005, 03:44 PM
hey!
where did u get the spacer kit? can u post a link?
evomind
11-01-2005, 03:49 PM
is this it??
http://www.gstyle4u.com/.sc/ms/dd/H3%20Performance--H3%...202006%20HUMMER%20H3 (http://www.gstyle4u.com/.sc/ms/dd/H3%20Performance--H3%20Intakes/796/AIRAID%20THROTTLE%20BODY%20SPACER%20^2F%202006%20H UMMER%20H3)
Tommy36998
03-27-2006, 04:46 AM
How long to install?

Originally posted by evomind:
is this it??
http://www.gstyle4u.com/.sc/ms/dd/H3%20Performance--H3%...202006%20HUMMER%20H3 (http://www.gstyle4u.com/.sc/ms/dd/H3%20Performance--H3%20Intakes/796/AIRAID%20THROTTLE%20BODY%20SPACER%20%5E2F%202006%2 0HUMMER%20H3)
lotus4s
03-27-2006, 05:29 PM
Sweeeet!
kennyosemite
03-28-2006, 01:57 AM
Dang. Double dang. That ride rocks.
Huck BB62
03-28-2006, 06:11 AM
Originally posted by floridahummer:
HERE THEY ARE

How long did you drive it before installing the throttle body spacer? Are you going to install the airaid intake kit?
Steve - SanJose
04-01-2006, 09:49 AM
Serious bling with an offroad slant. Great pics.

S.
GLBLWARMR
04-01-2006, 11:37 AM
Sweet.
love the color.
ETD
04-04-2006, 11:26 AM
Man, that took you 6 hours? The yellow doesn't do much for me but your rig looks good!!! 6 Hours? That's a good case in the OR... Guess, I'll have to hire somebody if I want one somedays. Thanks for the pics.