 |
|
08-27-2010, 04:22 PM
|
 |
Hummer Professional
|
|
Join Date: Nov 2009
Location: Windermere, FL
Posts: 297
|
|
Two Questions About SUT Bed
1. How does the plastic floor of an SUT bed come off?
2. How do you clean the trays that catch debris in the drains of the bed?
Thanks,
Charles
__________________
White 2005 SUT, Lifted 7.5" via Fabtech/custom work, Fabtech Dirt Logic 2.25 shocks, 40x15.5x22 Toyo's, black 22" Fuel wheels, 4.88 gears, Dynatech long tube headers, Magnaflow exhaust, Air-raid intake, Superchips programmer, Edlebrock panhard bar, Cognito UCA's, Kryptonite tie rods, Cognito pitman/idlar arm gussets, Hotchkis swaybars and trailing arms, Amp Research steps, E&G fender flares, PIAA SMR's, smoked roof lights (bulbs removed), black suede headliner, 13" JL's under seat
|
08-27-2010, 04:51 PM
|
 |
Hummer Authority
|
|
Join Date: Jan 2008
Location: Gaithersburg, MD
Posts: 1,762
|
|
Re: Two Questions About SUT Bed
This probably won't answer your question...but may lend some insight.
__________________
CNTRY
DTOM
|
08-27-2010, 04:54 PM
|
|
Hummer Professional
|
|
Join Date: Nov 2009
Location: Windermere, FL
Posts: 297
|
|
Re: Two Questions About SUT Bed
Thanks. I'll have to study that. Haha
And to those of you looking at this picture, I need to get part #35 out.
__________________
White 2005 SUT, Lifted 7.5" via Fabtech/custom work, Fabtech Dirt Logic 2.25 shocks, 40x15.5x22 Toyo's, black 22" Fuel wheels, 4.88 gears, Dynatech long tube headers, Magnaflow exhaust, Air-raid intake, Superchips programmer, Edlebrock panhard bar, Cognito UCA's, Kryptonite tie rods, Cognito pitman/idlar arm gussets, Hotchkis swaybars and trailing arms, Amp Research steps, E&G fender flares, PIAA SMR's, smoked roof lights (bulbs removed), black suede headliner, 13" JL's under seat
|
08-27-2010, 05:01 PM
|
|
Hummer Authority
|
|
Join Date: Jan 2008
Location: Gaithersburg, MD
Posts: 1,762
|
|
Re: Two Questions About SUT Bed
I think you're on the right track...to get to 35 I bet you have to take 30 (and possibly 31) out; otherwise they'd show it on the diagram like 29 (above 30).
Good luck.
__________________
CNTRY
DTOM
|
08-27-2010, 05:04 PM
|
|
Hummer Professional
|
|
Join Date: Nov 2009
Location: Windermere, FL
Posts: 297
|
|
Re: Two Questions About SUT Bed
That's kind of what I figured. I'm thinking that the bolts for the tie downs are what hold the plastic in place.
__________________
White 2005 SUT, Lifted 7.5" via Fabtech/custom work, Fabtech Dirt Logic 2.25 shocks, 40x15.5x22 Toyo's, black 22" Fuel wheels, 4.88 gears, Dynatech long tube headers, Magnaflow exhaust, Air-raid intake, Superchips programmer, Edlebrock panhard bar, Cognito UCA's, Kryptonite tie rods, Cognito pitman/idlar arm gussets, Hotchkis swaybars and trailing arms, Amp Research steps, E&G fender flares, PIAA SMR's, smoked roof lights (bulbs removed), black suede headliner, 13" JL's under seat
|
08-29-2010, 07:18 AM
|
 |
Hummer Novice
|
|
Join Date: Feb 2009
Location: Southern Indiana
Posts: 21
|
|
Re: Two Questions About SUT Bed
If you just need to clean them out, take a flat blade screwdriver and remove the covers (#29 in blow up). They are each held in by 4 tension prongs. Just pop 'em out. Then take your screwdriver and a pair of needlenose pliers to dig out the hard to remove stuff. Finish with a blast of water...
You can also just clean them out from below the truck with your finger, but they are easier from the top.
__________________
2007 Hummer H2 Yellow SUV
37"x13.5"x20" Toyo Open Country MT's, 20x10 Method Racing 301's, Fox 2.0 Performance Series Shocks, Truxx Level kit, color matched grill, (Almost) all chrome removed, Removeable U-steps, Factory All weather mats, Gobi flip-up front plate, Factory brush guard
|
08-30-2010, 03:42 AM
|
|
Hummer Professional
|
|
Join Date: Nov 2009
Location: Windermere, FL
Posts: 297
|
|
Re: Two Questions About SUT Bed
I got the trays out and cleaned them.
The reason I was asking about the "floor" was because I noticed there's a small gap where acorns and such could get under it, and I wanted to take it off and clean it.
__________________
White 2005 SUT, Lifted 7.5" via Fabtech/custom work, Fabtech Dirt Logic 2.25 shocks, 40x15.5x22 Toyo's, black 22" Fuel wheels, 4.88 gears, Dynatech long tube headers, Magnaflow exhaust, Air-raid intake, Superchips programmer, Edlebrock panhard bar, Cognito UCA's, Kryptonite tie rods, Cognito pitman/idlar arm gussets, Hotchkis swaybars and trailing arms, Amp Research steps, E&G fender flares, PIAA SMR's, smoked roof lights (bulbs removed), black suede headliner, 13" JL's under seat
|
| Thread Tools |
Search this Thread |
|
|
|
| Display Modes |
 Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT +1. The time now is 04:16 PM.
|
