Hummer Forums by Elcova  
Forums - Home
Source Decals

Source Motors
Custom. Accessories.

H2 Accessories
H3 Accessories
Other Vehicles

H2 Source

H2 Member Photos
H2 Owners Map
H2 Classifieds
H2 Photo Gallery
SUT Photo Gallery
H2 Details

H2 Club

Chapters
Application

H3 Source

H3 Member Photos
H3 Classifieds
H3 Photo Gallery
H3 Owners Map
H3 Details
H3T Concept

H1 Source

H1 Member Photos
H1 Classifieds
H1 Photo Gallery
H1 Details

General Info

Hummer Dealers
Contact
Advertise

Sponsored Ads










 


Source Motors - custom. accessories.


Go Back   Hummer Forums by Elcova > Hummer H2 Discussion Forums > General H2 Discussion

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 07-29-2014, 02:21 AM
dna dna is offline
Hummer Veteran
 
Join Date: Jun 2005
Posts: 132
dna is off the scale
Default Help - changed my plugs now H2 runs like @#$%

After 200kms I thought it would be a good idea to change the plugs and wires for the 1st time. Bought the iridium (41-110) and OEM wires. With doing only limited googling, I thought these were supposed to be gapped at .06mm so I did that (they were 0.04mm out of the box).

After installed these new plugs, the idle was smooth and revved nice. Took it for a drive and the truck could barely get over 100 km/hr. After a few minutes I got P0151 (maf sensor) and p0300 (random misfires).

So I pulled all plugs out again and regapped back to 0.04. Installed them, but same thing. Could barely get over 100km/h and same 2 obdii codes.

Could I have damaged the plugs when I first gapped them? My method was sticking a flathead driver into the gap and lifting up - could this have damaged the iridium tip?? Is there anyway I can tell if the plugs are bad other than buying a whole new set?? BTW - I dropped one of them about 3' onto a concrete floor - when it first happened I looked at it and it looked fine. Could that have damaged that one, and is it possible if I have only 1 bad plug that I'd get these symptoms and codes?? I would have thought if only one plug was bad that the p0300 would have given me a number in the last digit to tell me which cyclinder is misfiring - doesn't p0300 mean all (or more than 1) cylinders are misfiring??

Thanks
Reply With Quote
  #2  
Old 08-01-2014, 09:23 PM
glennf1 glennf1 is offline
Hummer Veteran
 
Join Date: Nov 2011
Posts: 163
glennf1 is on a distinguished road
Default Re: Help - changed my plugs now H2 runs like @#$%

My bet is you either bumped the plug at the MAF during your plug swap or there is a break in that wiring. Without the MAF signal it will do exactly what you described.
Reply With Quote
  #3  
Old 08-02-2014, 03:48 AM
dna dna is offline
Hummer Veteran
 
Join Date: Jun 2005
Posts: 132
dna is off the scale
Default Re: Help - changed my plugs now H2 runs like @#$%

Checked the maf plug and it was fine. Still have the issue. I guess it could be a coincidence and my maf sensor has gone bad. Is there a way to test the sensor?

Otherwise if maf is good and maf plug well connected, any other ideas?

Could it be my cat. I have one that is going bad. Been looking for a replacement for a few weeks now. Though prior to the plug swap, only issue I had was rattlin (no codes). Maybe with the new plugs and wires, with the extra power it was enough to fully plug my cat. Heard that a plugged cat will give p0300 codes - though would that also give the maf code?

Thanks
Reply With Quote
  #4  
Old 08-02-2014, 09:37 PM
glennf1 glennf1 is offline
Hummer Veteran
 
Join Date: Nov 2011
Posts: 163
glennf1 is on a distinguished road
Default Re: Help - changed my plugs now H2 runs like @#$%

MAF itself could be bad or the wiring from it going to the computer. My only other guess would be a forward O2 sensor. If your cat was bad the rear O2 would catch it and that's only for emissions anyway, the forward O2 is for Air/Fuel. The codes are your friend.. it would not have thrown a MAF sensor code unless it was out of range or not receiving feedback from it. Unplug your MAF sensor and drive it. If there is no difference I would replace it.
Reply With Quote
  #5  
Old 01-30-2015, 04:58 PM
inputapmech inputapmech is offline
Elcova Rookie
 
Join Date: May 2012
Posts: 6
inputapmech is on a distinguished road
Default Re: Help - changed my plugs now H2 runs like @#$%

I think your spark gap is 1.02mm.... That might be the problem
Reply With Quote
  #6  
Old 02-02-2015, 01:09 PM
Camou2 Camou2 is offline
Hummer Veteran
 
Join Date: Oct 2007
Location: Annapolis, MD
Posts: 123
Camou2 is on a distinguished road
Default Re: Help - changed my plugs now H2 runs like @#$%

Quote:
Originally Posted by inputapmech
I think your spark gap is 1.02mm.... That might be the problem

1.02mm is the same as a gap of .04 and that is what the plugs should be gapped at,, suspect just coincidence but probably MAF problem
__________________
www.thehummerclubinc.com
2004 H1 Softtop
2006 H2
2008 H3 Alpha
Reply With Quote
  #7  
Old 02-15-2015, 10:37 PM
glennf1 glennf1 is offline
Hummer Veteran
 
Join Date: Nov 2011
Posts: 163
glennf1 is on a distinguished road
Default Re: Help - changed my plugs now H2 runs like @#$%

Did you ever figure it out?
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 04:14 AM.


Powered by vBulletin Version 3.0.7
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.