Hummer Forums by Elcova  
Forums - Home
Source Decals

Source Motors
Custom. Accessories.

H2 Accessories
H3 Accessories
Other Vehicles

H2 Source

H2 Member Photos
H2 Owners Map
H2 Classifieds
H2 Photo Gallery
SUT Photo Gallery
H2 Details

H2 Club

Chapters
Application

H3 Source

H3 Member Photos
H3 Classifieds
H3 Photo Gallery
H3 Owners Map
H3 Details
H3T Concept

H1 Source

H1 Member Photos
H1 Classifieds
H1 Photo Gallery
H1 Details

General Info

Hummer Dealers
Contact
Advertise

Sponsored Ads










 


Source Motors - custom. accessories.


Go Back   Hummer Forums by Elcova > Hummer H2 Discussion Forums > Technical Discussion and Customizing your H2

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 01-15-2016, 09:51 PM
glennf1 glennf1 is offline
Hummer Veteran
 
Join Date: Nov 2011
Posts: 163
glennf1 is on a distinguished road
Default Just had to do the infamous blend door replacement

Unfortunately I had to replace the passenger side blend door actuator which is the harder one to get to at the top of the dash. I pretty much followed the instructions here on this forum and others and it was pretty much spot on. It cost a whole $34 for it. I guess our rigs are starting to show their age!
Reply With Quote
  #2  
Old 06-07-2016, 10:54 PM
Lucky1 Lucky1 is offline
Hummer Professional
 
Join Date: Aug 2005
Location: Dallas, Texas
Posts: 314
Lucky1 is off the scale
Default Re: Just had to do the infamous blend door replacement

What tool did you use to remove the 2 bolts on the blend door actuator ? I can't seem to get the bolt closest to the driver's side out with the 8 mm box end wrench I'm using. It's apparently too long or I don't know the truck. Thanks in advance.
__________________
Pimpin 8 E Z but somebodys gotta do it .
Reply With Quote
  #3  
Old 06-11-2016, 07:11 PM
glennf1 glennf1 is offline
Hummer Veteran
 
Join Date: Nov 2011
Posts: 163
glennf1 is on a distinguished road
Default Re: Just had to do the infamous blend door replacement

8mm box wrench. Maybe your's is too long? Mine has a slight angle also. I remember having to have one hand in through where the passenger airbag switch is and the other through the top and could only make small 1/8 of turns or less. Make sure you have it installed before you plug it in too.
Reply With Quote
  #4  
Old 06-23-2016, 08:31 PM
Lucky1 Lucky1 is offline
Hummer Professional
 
Join Date: Aug 2005
Location: Dallas, Texas
Posts: 314
Lucky1 is off the scale
Default Re: Just had to do the infamous blend door replacement

Thanks Glenn. I think my box end wrench was too long so I just brute forced it. Lol.. I got it out and in with a sacrificial crack in my air duct tube. A little bit of aluminum tape and all is well. p
__________________
Pimpin 8 E Z but somebodys gotta do it .
Reply With Quote
  #5  
Old 07-10-2016, 03:53 AM
fllaw1 fllaw1 is offline
Hummer Novice
 
Join Date: Oct 2010
Posts: 23
fllaw1 is on a distinguished road
Default Re: Just had to do the infamous blend door replacement

Any photos taken apart?
Reply With Quote
  #6  
Old 08-08-2016, 01:06 AM
glennf1 glennf1 is offline
Hummer Veteran
 
Join Date: Nov 2011
Posts: 163
glennf1 is on a distinguished road
Default Re: Just had to do the infamous blend door replacement

I didn't even think to take pics. There are a few videos on you tube that might help if you are trying to get a visual. Just search H2 blend door.
Reply With Quote
  #7  
Old 05-05-2017, 09:54 PM
Nielsen Nielsen is offline
Hummer Novice
 
Join Date: Jul 2004
Location: Pensacola, Florida
Posts: 15
Nielsen is an unknown quantity at this point
Default Re: Just had to do the infamous blend door replacement

Glenn,... Can you verify for me that your passenger blend door had three fasteners or two,... also the price of $34.00 is good,... I'm seeing prices in the hundreds for the passenger blend door ???? Nielsen
Reply With Quote
  #8  
Old 10-05-2017, 08:23 PM
DRTYFN's Avatar
DRTYFN DRTYFN is offline
Hummer Messiah
 
Join Date: Nov 2002
Location: PDX
Posts: 2,367,817
DRTYFN is an unknown quantity at this point
Default Re: Just had to do the infamous blend door replacement

I need to do the recirculated actuator. Too lazy/busy now.
Reply With Quote
  #9  
Old 03-08-2018, 04:11 AM
glennf1 glennf1 is offline
Hummer Veteran
 
Join Date: Nov 2011
Posts: 163
glennf1 is on a distinguished road
Default Re: Just had to do the infamous blend door replacement

Quote:
Originally Posted by Nielsen
Glenn,... Can you verify for me that your passenger blend door had three fasteners or two,... also the price of $34.00 is good,... I'm seeing prices in the hundreds for the passenger blend door ???? Nielsen


I'm sure you already got it by now but for anyone reading it's three fasteners. My $34 one is still working fine. It's only an actuator.. not much to it.
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 01:36 AM.


Powered by vBulletin Version 3.0.7
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.