Hummer Forums by Elcova  
Forums - Home
Source Decals

Source Motors
Custom. Accessories.

H2 Accessories
H3 Accessories
Other Vehicles

H2 Source

H2 Member Photos
H2 Owners Map
H2 Classifieds
H2 Photo Gallery
SUT Photo Gallery
H2 Details

H2 Club

Chapters
Application

H3 Source

H3 Member Photos
H3 Classifieds
H3 Photo Gallery
H3 Owners Map
H3 Details
H3T Concept

H1 Source

H1 Member Photos
H1 Classifieds
H1 Photo Gallery
H1 Details

General Info

Hummer Dealers
Contact
Advertise

Sponsored Ads










 


Source Motors - custom. accessories.


Go Back   Hummer Forums by Elcova > Hummer H2 Discussion Forums > Technical Discussion and Customizing your H2

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 12-06-2007, 01:26 PM
Rene S. Nielsen Rene S. Nielsen is offline
Hummer Veteran
 
Join Date: Oct 2005
Location: Denmark
Posts: 126
Rene S. Nielsen is off the scale
Default New engine help please

Hi

I need some help. The engine in my H2 can't be fixed, since it's not posible to get a new cylinder that's a bit bigger (is this correct ?)

A new engine will cost me about 12000 $ (stated by the workshop here in Denmark).

I have also been told that I can't just by another Vortec 6.0 liter engine off ebay, unless it was originally pulled from a H2, because there is a difference on this engine (?????)

Would any of you have a good source for a new / lightly used engine (cheap) that would fit my H2. And one that would be willing to ship overseas.

No Duramax please, refitting this here in DK would cost a fortune.

Regards
Rene
Reply With Quote
  #2  
Old 12-06-2007, 02:53 PM
MVR 155's Avatar
MVR 155 MVR 155 is offline
Hummer Professional
 
Join Date: Aug 2007
Location: Bartlett, Illinois
Posts: 486
MVR 155 is on a distinguished road
Default Re: New engine help please

$12000 sounds waaaaaay out of line for a new engine, if your heads are not damaged all you need is a new short block, I believe our H2's use the exact same engine as any of the 3/4 trucks (base 6.0L) and the Escalade and Denali's. Sounds like they are trying to royally stick it up your A$$ on this. Dont let them.
__________________
2008 H2 SUV Luxury: Solar Flare ext/Black int

SOLD 2006 H2 SUV Luxury: Pewter ext/Black int.

2002 Corvette Z06 Blue/Ebony (light mods)
1/4 mile: 11.661@118.86

2013 Audi S4

2002 Yamaha YZF R1 Blue/White
1/4 mile: 10.51@136

2006 Sea-Doo RXP (70.6mph GPS)
2005 Sea-Doo RXT
Reply With Quote
  #3  
Old 12-06-2007, 03:43 PM
Planohummer Planohummer is offline
Hummer Veteran
 
Join Date: Aug 2005
Posts: 184
Planohummer is an unknown quantity at this point
Default Re: New engine help please

Escalade and Hummer have their own short block, but it's not fundamentally different than any other GM 6.0 liter(upgraded pistons and rings). You can essentially buy any long block 6.0l and use your existing intake and exhaust setup. There are some subtle changes from year to year, so I'd try and get one from the same year vehicle.
Reply With Quote
  #4  
Old 12-08-2007, 04:03 AM
CrackerJackToy CrackerJackToy is offline
Hummer Novice
 
Join Date: Dec 2007
Posts: 15
CrackerJackToy is on a distinguished road
Default Re: New engine help please

Bore cylinder walls out...bigger stronger high compression pistons and better rods. Good to go and will have more power.
Reply With Quote
  #5  
Old 12-08-2007, 04:23 AM
Yetti Yetti is offline
Hummer Expert
 
Join Date: Apr 2004
Location: Grass Lake,Mi
Posts: 583
Yetti is an unknown quantity at this point
Default Re: New engine help please

www.junkyarddog.com
I'm suprised you don't have a better sourse for parts. I know theres tons of GM stuff in Iceland. have you tried looking down in North Africa? there may be loads of parts down by Dubia & Kuwait
__________________
Yetti
----------------------------
www.greatlakes4x4.com
www.wegotmud.com
www.glfwda.org
Reply With Quote
  #6  
Old 12-10-2007, 02:12 PM
Rene S. Nielsen Rene S. Nielsen is offline
Hummer Veteran
 
Join Date: Oct 2005
Location: Denmark
Posts: 126
Rene S. Nielsen is off the scale
Default Re: New engine help please

Hi CrackerJackToy

This was actually my first option, but the shop told me that they couldn't get new pistons to fit. They told me this was not made since then it might not meet the emmisions (spelling ??) regulation.

I just need them i oversize 1....

Rene

Ps. Did find another engine in the US, trying to get it shipped to Denmark right now
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 08:48 PM.


Powered by vBulletin Version 3.0.7
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.