Torsion Bar Information

[cestwick]

Originally Posted by HummBebe

OK,thank you.

Did you keep the front shocks stock? You had noted that you turned your T-Bars, 7-8 turns, did you not get longer shocks for the front???

Yes I kept the front shocks factory. You would not benefit much from longer shocks in front because you are limited in the travel by the whole geometry of the front suspension. I do believe the brackets from Truxx would help the stiff front end if you crank the torsion bars up to the point it tops out the shock. The top shaft on the shock is long enough I just put a spacer between the shock and the lower bushing washer, efectively alowing the shock to sit lower in the mount and let it extend a little further.

[HummBebe]

BTT, anybody seen cestwick???

I have a couple of questions.....

[cestwick]

Originally Posted by HummBebe

BTT, anybody seen cestwick???

I have a couple of questions.....

Last i know he was working at a T*y**a Dealership.

What can i do for ya?

Chris

[HummBebe]

I had my shackles built, just wanted to know if there is any feedback from your set up? It's been a while since you installed.

I have a 2" extended shackle.

[HummBebe]

Also, I found a Rancho 99227, from a 1 ton suburban 4" lift REAR, is 1" longer, all the same mounting, closed barpin, etc., and I think it's the same as the BDS you mentioned earlier in this thread.

I found some Hellwig adjustable end links, and some helper springs.

The Avalanche front shock Rancho 99268, is the same size as the H3 but with 6"'s of travel, vs 2.34 that Rancho has for the H3, and 4"'s that the stock shock has.

Think this will work?

[evldave]

Originally Posted by HummBebe

Also, I found a Rancho 99227, from a 1 ton suburban 4" lift REAR, is 1' longer, all the same mounting, closed barpin, etc., and I think it's the same as the BDS you mentioned earlier in this thread.

...

Think this will work?

Only if you put a 12" lift on your Hummer

[HummBebe]

1"

[cestwick]

Originally Posted by HummBebe

Also, I found a Rancho 99227, from a 1 ton suburban 4" lift REAR, is 1" longer, all the same mounting, closed barpin, etc., and I think it's the same as the BDS you mentioned earlier in this thread.

I found some Hellwig adjustable end links, and some helper springs.

The Avalanche front shock Rancho 99268, is the same size as the H3 but with 6"'s of travel, vs 2.34 that Rancho has for the H3, and 4"'s that the stock shock has.

Think this will work?

I don't see why that wouldnt work. The front shock will have more travel then you can use with the front bump stops, but if you raise the bars a little more then you have now to match the rear you will need the extra travel to keep front for topping out the shock and causeing the rough ride.

[cestwick]

Originally Posted by HummBebe

I had my shackles built, just wanted to know if there is any feedback from your set up? It's been a while since you installed.

I have a 2" extended shackle.

I can't say that i have had any problems in the back or noticed anything good or bad, other then the fact that with extended travel in the rear from long shocks you will have to change sway bar links or remove the sway bar all togather(which is what i did). The stock links will not twist enough and will pop out of the joint when articulated.

[HummBebe]

Like I said, Hellwig products makes the end links that are adjustable. I called and they said it will work for an H3...

Are they important to have? or have you been OK without your Sway Bar?

[cestwick]

Originally Posted by HummBebe

Like I said, Hellwig products makes the end links that are adjustable. I called and they said it will work for an H3...

Are they important to have? or have you been OK without your Sway Bar?

I havent noticed one bit that the rear sway bar isnt there....If you look at 90% of the trucks on the road they dont have rear sway bars