Exhaust w/ a Growl !!

[HUMMERcustoms.com/TAZ]

PLEASE EXCUSE ME THIS SHOULD HAVE BEEN IN THE THREAD CONCERNING BRUTES CUT OUTS. Hope anyone may gain some help from this anyway. It is the reason I take time to share my 4 years of working on H2's. I think Dragon and I will be on our 3rd complete tear down inside and out this summer including a complete media blast to take all paint off to bare metal. So Dragon and I should be able to help at least from seeing the beasts parts tagged and numbered etc. from every area a part can be removed. Sorry for wrong thread to be in.

Many routes to great exhaust sound. Just a matter of who you choose to let lead you through that maze.

I have been as big a supporter of Allen Nelson tuning as you could find through a search of my threads and one of the first to bring him up to the forum 3 or 4 years ago through some work with STS TURBOS that Allen provide all tunes for their kits. I got to know him outside this world first. He cannot be beat.

Nelson cannot be beat unless as He says you dare step into the world of using software to tune your own ride then you can push the limit. Allen is a businessman and will never push a tune to point of it being a danger of damaging your engine. Yet it will come as close to a self tune situation with a safety margin as he feels it should. If you choose to risk blowing up your stuff that is on you as he told me. Allen will not do that as it is not ethically his call to make and he has to consider liability issues.

If you want to start to experitment with tuning I recommened you use HPTUNERS.com. It loads on your laptop and you can play with scenarios on the computer and see what it would look like. There forum is the best training school I have ever seen for a product. Most of the time 1 of the 3 owners are moderators and answering questions.

I must say they have been my sponsor for tuning since 2005. I sought them out not the reverse. I saw the early product just before they began to really roll after fall 2005 SEMA. I was hooked up with them before etc. and then 2006 just took off for them and 3 guys that never deserved it more. I told them what I had and what I dreamed of doing with their software and was told not sure it would do that. It did do that so the learned while i learned.
I'm telling this so anytime I push HPTUNERS.com I have 2 sides that I do it for and the practical use side is the strongest reason.

Go to site and if nothing else just start reading forums and picking up more knowledge about how the whole combustion stuff works even if you have Nelson do it. If he asks a question you will have a better answer or understand why he asks it anyways.

Brute the only reason I see that putting the cut outs ahead of the cats is it would then not give your ECM the sensor info the rig needs for any kind of tune as some of sensors and readings needed are located on intake of cat and exit sides.

Brute how is the reverb on the interior of the rig with cutouts right under the cabin? I had my tailpipes turned down on my Dynatech setup right in front of rear axle at first and by the time I drove it home my insides felt like jelly. So over the rear axle they went and then all good. I was looking at cutouts later but looking at running a second set of pipe out in front of rear tires. Now just for a run I figure your location should be just fine. I would appreciate your feedback on that situation. Thanks Brute Buddy!

TAZ

[Stainless]

I have the Corsa "sport" catback SS system on my 2008. and it Growls for sure!!

love it, love it, love it!!

SJK

[SUT Dan]

Fantastic input so far and w/in 12 hrs. No doubt I jumped in the correct forum with well educated hardcores. Thanks for the 411 folks !

Dan

[devilsfan]

Corsa sport. Hands down. You can hear it on their website.

Had problems with their reliability, tho. If you don't offroad, you'll be fine.

Stacy

[peppers&eggs]

Have a Flowmaster on my rig and it sounds real nice. It's not loud when your crusin but if you get on it, it has a nice deep RoaR.