H20 Corner Ladder

[seventwozero]

I could be wrong, but I've only seen those on one truck, the guy posts under the name AdamInCO, or something like that. There maybe have been 1 more set, his is the only truck I've seen though.

I'd love a pair... but I would be shocked if you found them for sale somewhere.

[SummitUp]

Yeah, I know Adam and he did have a pair of those "corner ladders". However, they originally were not sold as ladders, but as corner body protection guards (the corner guards are really too close to the body to get your feet on them to use as ladders). Adam also had dual ladders in addition to these corner body guards. Here's some pics of Adams H2, before he sold it a few years ago:

[seventwozero]

If it's any consolation, I recall a story where he rolled this truck into something (a tree?), the corner guard took the impact and ended up causing more damage to the truck than had he not had them on there. I want to say he ended up breaking out the glass and causing a crease in the rear quarter, below the window.

It's a bummer H20 isn't in business, their winch bumper and roof racks were badass.

If you can figure out how they are attached at the bottom it probably wouldn't cost all that much to have a set fabbed up.

[LoJac963]

Originally Posted by seventwozero

If you can figure out how they are attached at the bottom it probably wouldn't cost all that much to have a set fabbed up.

That's exactly what I was going to say. There isn't a whole lot of metal work other then some bends on those things. Just have to figure out the attachment points which I'm sure are pretty similar to the ladders on the market.

[guruerror]

From all the pics I've seen from various angles there doesn't appear to be any attachment points at the bottom...maybe a small bracket slips in the wheel-well where the fender flare splits from the corner bumper piece; but I don't know about around back by the hatch. It sets out so far from the body of the truck that we should see some sort of bracket or something...

Perhaps that's one of the reasons that it caused so much damage when it took the impact...if the bottom didn't have proper support it would just bend right in. Perhaps he designed it as more of a ladder and less of a guard/ladder.

EDIT: I take that back...I think the rear bracket can be seen in this pic. If that's it I think it's a little weak. I'd liked to see something beefier than that; and maybe another in the middle.

[VegasMike]

Originally Posted by guruerror

From all the pics I've seen from various angles there doesn't appear to be any attachment points at the bottom...maybe a small bracket slips in the wheel-well where the fender flare splits from the corner bumper piece; but I don't know about around back by the hatch. It sets out so far from the body of the truck that we should see some sort of bracket or something...

Perhaps that's one of the reasons that it caused so much damage when it took the impact...if the bottom didn't have proper support it would just bend right in. Perhaps he designed it as more of a ladder and less of a guard/ladder.

EDIT: I take that back...I think the rear bracket can be seen in this pic. If that's it I think it's a little weak. I'd liked to see something beefier than that; and maybe another in the middle.

That tube you have highlighted looks to me like the down tube for the straight ladder on the back. If you look closely it looks further away in the picture, and if you look at the other pictures above showing the back view, it makes sense that it's a part of the standard ladder, and not attached to the corner ladder. Looking at it further, you can clearly see that tube is behind the taillight guard, and the corner ladder can not extend beyond the that guard in order to allow the hatch to open..

It looks like the bottom of the corner ladder has no support.

[guruerror]

Originally Posted by VegasMike

...It looks like the bottom of the corner ladder has no support.

Agreed. That's a bad design in my book. Looks good, but bad design.

[seventwozero]

Originally Posted by guruerror

From all the pics I've seen from various angles there doesn't appear to be any attachment points at the bottom...maybe a small bracket slips in the wheel-well where the fender flare splits from the corner bumper piece; but I don't know about around back by the hatch. It sets out so far from the body of the truck that we should see some sort of bracket or something...

Perhaps that's one of the reasons that it caused so much damage when it took the impact...if the bottom didn't have proper support it would just bend right in. Perhaps he designed it as more of a ladder and less of a guard/ladder.

EDIT: I take that back...I think the rear bracket can be seen in this pic. If that's it I think it's a little weak. I'd liked to see something beefier than that; and maybe another in the middle.

Not to say anyone is wrong here, because I just can't see anything either, but I have a really hard time believing that H20 would produce something like that WITHOUT some sort of support on the lower end of it. I mean, from what I understand, the products that H20 made for a short time were some of the best on the market.

I'm thinking there is something hidden on that lower rail, on the side of the truck/guard, just below the rear marker light. There is metal there that the bracket could be attached to, but there isn't a whole lot there, and what is there probably isn't that strong.

The top looks pretty self explanatory, some sort of system that bolts up to the roof rail, similar to a roof rack.

IIRC, HumBeBe knows the guy that ran H20, and built all this stuff. Maybe she could offer insight on how they attached, or sweet talk him into doing a small run of them again! I would certainly buy a set.

Edit: the more I look at those photos, and start to remember, I think this truck also had the H20 front and rear bumpers. I'm wondering if those guards are attached directly to the rear bumper...

[VegasMike]

More pics from that thread: