$600 for offroad lights instalation?

[FLA_H3]

Originally Posted by RubHer Yellow Ducky

Get a quote from VERA HUMMER in Pembroke Pines. They are only 30 minutes north of Williamson.

Also correct me if I am wrong. If its a lease won't the lights stay with the H-3 when you turn it in.

RYD (miami, near metrozoo)

On a lease any aftermarket accessories can come off as long as they do not leave any markings or holes. I do it all the time. This also keeps me from spending alot of money on upgrades.

[www.miami3drenders.com]

i will check with VERA HUMMER in Pembroke Pines
i saw the instalation tutorial and completely freak me out, i'm more the computers kinda guy. hard drives, proccesors, memories, etc.
thanks again guys

[Crash ?]

Originally Posted by www.miami3drenders.com

i saw the instalation tutorial and completely freak me out, i'm more the computers kinda guy. hard drives, proccesors, memories, etc.

Seriously.. If you can crack open a PC, add a hard drive, upgrade the processor and memory, you can do this.. It's all one step at a time stuff.. Not even any multi-processing..

As far as drilling holes in body panels.. I haven't looked at the directions close to see if it HAS to be done, but it's just basic stuff..

1. Lay out the template
2. Mark your spots with a dry erase marker
3. Remove template
4. Have a smoke or a beer while a friend puts the template back on to double check
5. Remove it and put it back on yourself to triple check it.
6. Make sure everything lines up the same 3 times IN A ROW before proceeding. If you have to lay everything down and start again tommorow with a fresh less frustrated look on things.
7. Take a hole punch and a hammer to MARK a small dent for the drill bit so it won't wander off the mark.
8. Drill a starter hole with a small bit.
9. Enlarge the hole with a bit half way between the starter bit and the size the hole will end up.
10. Finally drill the hole to the correct size..
11. Spray a bit of WD40 on the spot your drilling BEFORE you drill and a little bit while you are drilling.
12. DO NOT WIPE METAL SHAVINGS UP, they'll scratch the paint. Blot them and the WD40 up with a fuzzy shop rag.
13. Once the shavings are gone, clean up the WD40 with soapy water or 409.
14. If you're paranoid about rust, use touchup paint around the edges of the hole...

See..?? Simple..

[K9sH3]

Originally Posted by Crash ©

Seriously..


See..?? Simple..

HAHAHAHAHA!

For some reason I am finding that funny as sh**

[Crash ?]

Originally Posted by K9sH3

HAHAHAHAHA!

For some reason I am finding that funny as sh**

Really it is.. I put a spoiler fin on my wifes RX-8 in about 45 minutes... Without having a clue what I was doing to start with.. Basically the same proceedure..

Think about it.. MOST of the cats working in body shops aren't exactly rocket scientists.. Typically if it hadn't been for the option of being able to go to a Vo-Tech school their senior year of high school they would have been drop-outs if they didn't flunk out for not being able to pass english, history or science..

Bet there's some of those guys here that are gonna flame my ass off for that comment.. Sooo... Lemme say this.. A friend of mine in High School was kinda like that.. Never did get his diploma because he couldn't pass American History.. Couldn't pass to get his GED and after 4 tries of that he gave up on it.. Worked his ass off at two and three jobs and by the time he was 21, he OWNED a car, 2 trucks, a 600cc Quad and 2 motorcycles.. 2 years later he BOUGHT a house.. No note on any of it.. Last I heard he's still getting along better than I am as far as income goes..