Need some diff help!!

[jarek m]

At the end of the shaft there is a spring that prevents the shaft from sliding out, you need to apply outward pressure on the shaft to get the spring inside the diff to align and then give it a hit with a 2.5er. Some springs don't come out in one piece there for hawing a new set handy is nice, my came right out, looks like yours are a little more stubborn that's all

This is a different application but the end of the spline looks same #1.

[jarek m]

#30

[lx4life]

YOU ARE THE MAN JAREK I WAS REALLY TRYING NOT TO BOTHER YOU!!!!! THANKS SO MUCH, its just that these things are so expensive to replace if I break it and I really don't want to go to the stealership and have them do it, cause I could use that money for aftermarket parts you know what I mean. This iste is one of the best around, I have to work until tomorrow afternoon(32hr work day) so i will try again tomorrow after work

[jarek m]

Originally Posted by lx4life

YOU ARE THE MAN JAREK I WAS REALLY TRYING NOT TO BOTHER YOU!!!!! THANKS SO MUCH, its just that these things are so expensive to replace if I break it and I really don't want to go to the stealership and have them do it, cause I could use that money for aftermarket parts you know what I mean. This iste is one of the best around, I have to work until tomorrow afternoon(32hr work day) so i will try again tomorrow after work

It's no bother at all.

[twr]

hi this should help you out with the front diff.





1 - Front Drive Axle Inner Shaft
2 - Front Drive Axle Inner Shaft Retaining Ring
3 - Front Drive Axle Inner Shaft Seal
4 - Front Drive Axle Inner Shaft Bearing
5 - Front Drive Axle Inner Shaft Housing
6 - Front Drive Axle Housing Bracket Bushing
7 - Front Drive Axle Inner Shaft Housing Bolt
8 - Front Differential Carrier Case Bolt
9 - Front Differential Carrier Case Half
10 - Front Differential Bearing Adjuster Lock Pin
11 - Front Differential Bearing Adjuster Nut and Sleeve
12 - Front Differential Case Side Bearing Cup
13 - Front Differential Case Side Bearing
14 - Front Differential Ring Gear Bolt
15 - Front Differential Pinion Gear Shaft
16 - Front Differential Case
17 - Differential Pinion Gear Shaft Lock Bolt
18 - Differential Pinion Gear Thrust Washer
19 - Differential Pinion Gear
20 - Differential Side Gear Thrust Washer
21 - Differential Side Gear
22 - Front Differential Side Gear Spacer
23 - Differential Pinion Gear Thrust Washer
24 - Differential Pinion Gear
25 - Front Differential Side Gear Spacer
26 - Differential Side Gear
27 - Differential Side Gear Thrust Washer
28 - Front Differential Ring Gear
29 - Front Differential Case Side Bearing
30 - Front Differential Side Gear Bearing Cup
31 - Front Differential Case Half Lock Pin
32 - Front Differential Case Half Lock Pin
33 - Front Differential Carrier Case Half
34 - Front Differential Carrier Bushing
35 - Front Differential Drive Pinion Gear
36 - Front Differential Drive Pinion Gear Inner Bearing Shim
37 - Front Differential Drive Pinion Inner Bearing
38 - Front Differential Drive Pinion Inner Bearing Cup
39 - Front Differential Drive Pinion Gear Bearing Spacer
40 - Front Differential Drive Pinion Gear Outer Bearing Cup
41 - Front Differential Drive Pinion Gear Outer Bearing
42 - Front Differential Drive Pinion Bearing Gear Oil Seal
43 - Front Differential Drive Pinion Bearing Gear Yoke
44 - Front Differential Drive Pinion Bearing Gear Yoke Washer
45 - Front Differential Drive Pinion Bearing Gear Yoke Nut
46 - Front Differential Carrier Oil Drain Plug Washer
47 - Front Differential Carrier Oil Drain Plug
48 - Front Differential Carrier Oil Fill Plug Washer
49 - Front Differential Carrier Oil Fill Plug
50 - Front Differential Carrier Hole Plug
51 - Front Differential Bearing Adjuster and O-Ring Seal
52 - Front Differential Bearing Adjuster Nut Lock
53 - Bolt
54 - Front Drive Axle Inner Shaft Bearing
55 - Front Drive Axle Inner Shaft Bearing
56 - Front Drive Axle Inner Shaft Retaining Ring
57 - Front Drive Axle Inner Shaft

[guruerror]

Originally Posted by twr

hi this should help you out with the front diff.

TWR: Did you pull that image from the EPC? If so, what version do you have?
You can find out by clicking Help then About...my build date is 23Jul2007 11:05 124

[twr]

Originally Posted by guruerror

TWR: Did you pull that image from the EPC? If so, what version do you have?
You can find out by clicking Help then About...my build date is 23Jul2007 11:05 124

hi guruerror, it came from Alldata. Its for a 2008 but the diffs are the same but the gear ratio is 410 to 1 in 2007 and down trucks and my 2008 is 373 to 1 do you need a picture of something?